At this time I like to put a lid on it, and burp it every day for a week, then it is ready to blast. A bin full of trim, waiting to be blasted, or made into canna oil. Packing your tube: Before packing make sure you now which end is which.
Most tubes come with a fine screen on the output. A coffee filter, cut just right to fit inside the rubber gasket. Attach the bottom to your tube and start packing from the top.
Put in about 3 handfuls, then pack lightly with a piece of PVC pipe, wooden rod, or similar. The material should be packed in so there is no air space around it, but not too tight.
This is part of the ART of blasting. The important thing here is that all fittings, hose clamps, rubber stoppers, etc, are secure! Tube packed and sealed2. Hot water will COOK your shatter, turn it dark and burn off potency and flavor. Approximately one ml can of butane for each ounce of material you are blasting. Nothing electric is turned on in the blasting area not fans, no nothing. Light switches taped down. Safety goggles 6. Dry, clean towel. Blast off! You will probably have a different tube, but you can use the same technique I use here.
I blast about 7 zips at a time, so I use 7 cans for each run. Check the tip of your butane can and put it into the top of your tube. It should fit tightly. Butane cans come with a variety of tips that you can exchange to find the best one that works with your tube. With both top and bottom valves wide open, start putting in butane at the top.
When your can runs out, close the top valve, remove the can, put on a new can, open the top valve. Work quickly. We want to flood the material as quickly as possible. Keep putting in butane at the top and soon it will start coming out the bottom. Let a good amount of butane come out about a full can , then close the bottom valve. Put in one more full can, if possible. Get in as much as you can, as quickly as you can.
I always get in 4 cans in my tube initially. After the tube is full of butane, take the tube out of the stand, and flip it upside down. This will help get the butane to the top of the tube and make sure all the material is soaked. If the tube has frost on it, or is sweating, you may want to wipe it down. DO NOT get water droplets into your oil. Let the tane flow to the top of the tube for about minutes.
We are simply trying to flood all of the material with tane at this point. Butane will come out. Let it keep coming out until only air is coming out. Close the valve, wait one minute for more butane to flow down, and open the valve again, letting tane out until it stops again.
Now, close the bottom valve and put in a total of two more cans. You may need to let a little pressure out the top or bottom of the tube to get in two more cans. Now, repeat step 2. Now, use one more can to flush everything out and get the last of it. Keep the bottom valve open slightly until only air is coming out. Do this a couple more times until you feel like all the tane is out.
Pull your double broiler rig out from under the blasting tube. This will prevent any water droplets from falling into our oil. At any time during the process, if you see water droplets on the tube, you can close the bottom valve, take the tube out and wipe it down, quickly. The water in your double broiler will be cool by now.
You can pour it out and use some warm water, but no warmer than bath water. Too hot, and you will cook off the flavorful terpenes. You will see some material in your tane that looks like a sea sponge. It is frozen moisture that was pulled out of your plant material. You can scoop it out with a fork, or leave it. If you leave it, you might risk trapping some moisture into the shatter, and it will pop and crackle on a hot nail.
I rarely pull it out, unless it is excessive. Keep watching it. The tane will slowly evaporate off. Here is where it is critical, NOT to use hot water. You can instantly ruin your oil. When it is almost done, I only use room temperature water. For the record, we are going into the house and getting warm water, and taking it outside. We are NOT using any kind of electric warming devices in the butane area.
Am I clear enough on this? Do not pop bubbles, do not swirl your oil around. Move it as little as possible. Any stirring and your shatter will not look clear at the end, and it will be more difficult to purge all the butane out of the oil. Now, we transfer our PTFE to our vac. If you lift of the PTFE out of your container, and the product is runny and about to spill out, then it is too thin. You need to wait longer. The oil should be the consistency of maple syrup.
There is no penalty for letting it sit a few extra minutes. It can be made from flowers as well as from leftover trimmings, making the possibilities endless. Before we get straight into it, you need to keep a few things in mind in order to make your own high quality BHO shatter ; the following list of accessories and objects are absolutely necessary for success.
Fill up your Roller Extractor tube, cutting up bits of your weed with scissors as you go — fill it up slowly and press it down as you go to make sure there are no empty pockets. In order to avoid any water getting into your extract, we recommend using a clean towel in order to hold the roller extractor; when frozen and then exposed to hot temperatures, it may end up sweating water from the melting moisture, which could fall into your tray and ruin your extract, making it turn out much softer than expected.
Do this until there is absolutely nothing left in the tray. Now that you have all of your extract on your silicone tray or oven paper , gather it all up in one lump. The best way to do this is place the tray in the fridge for a few moments — then, you can use the paper or tray itself, bending it and sticking both sides of the extract together until you eventually have one big lump — try not to use your hands for this. The resulting extract should be a thick, hard paste. Temperature may have been your issue here.
I do extractions using dry trim. I blast into round bottom flasks and let the butane evaporate. You should not need to heat the oil to remove the butane. I blast mL butane into roundbottom flask. I add a few mL ethanol Everclear proof. I let evaporate with a fan blowing over it. When it gets close to finishing I warm the flask warm water.
After that I dry it on a vacuum pump. If you need to heat use a warm water bath. Always end up with pale honey consistency. The role of the ethanol is to drive all of the butane out. The only trace of solvent that you now have in your oil is ethanol. Does ethanol have the same effect on pentane?
Yes, azeotropes at 34C Watch with pentane that you get decent purity or distill it before. Pentane can have traces of plasticizers and other higher boiling point impurities. The only reason I use butane and ethanol is that it is easy to get high purity.
Using any filter stacks in your extractor? What do you mean sucking harder? Please enlighten me. Ive been tryna shed extra terps using heat. Extracting trim with bho anyone know how to get a more golden colour? Hash and Stuff Extraction.
0コメント